MeshingParameters

MeshingParameters class

Represents settings used for creating a mesh representation of a brep or surface.

Namespace: Rhino.Geometry
MeshingParameters: references

Constructors (5)

MeshingParameters()

Initializes a new instance with default values.
Initial values are same as .

MeshingParameters(double density, double minimumEdgeLength)

Initializes a new instance with simple values, similar to that of Rhino's meshing slider interface.

MeshingParameters(double density)

Initializes a new instance with simple values, similar to that of Rhino's meshing slider interface.

MeshingParameters(MeshingParameters source)

Initializes a new instance copying values from source.
Initial values are same as .

MeshingParameters(SerializationInfo info, StreamingContext context)

Called by BinaryFormatter.Deserialize to create a new MeshParamaters object.

Properties (26)

ClosedObjectPostProcess

Gets or sets a value indicating whether or not to post process non-closed meshes that should be closed. If the Brep being meshed is closed, JaggedSeams = false, and ClosedObjectPostProcess = true, and the resulting mesh is not closed, then a post meshing process is applied to find and close gaps in the mesh. Typically the resulting mesh is not closed because the input Brep has a geometric flaw, like loops in trimming curve.

Coarse

Gets mesh creation parameters for coarse meshing.
This corresponds with the "Jagged and Faster" default in Rhino.

ComputeCurvature

Gets or sets a value indicating whether or not surface curvature data will be embedded in the mesh.

Default

Gets mesh creation parameters to create the default render mesh. Only use this if you plan on specifying your own custom meshing parameters.

DefaultAnalysisMesh

Gets mesh creation parameters to create the default analysis mesh.

DoublePrecision

Gets or sets a value indicating whether or not the mesh should have double precision vertices in addition to the floats.

FastRenderMesh

Gets mesh creation parameters to create the a render mesh when meshing speed is preferred over mesh quality.

GridAmplification

Gets or sets the grid amplification factor. Values lower than 1.0 will decrease the number of initial quads, values higher than 1.0 will increase the number of initial quads.

GridAngle

Gets or sets the maximum allowed angle difference (in radians) for a single sampling quad. The angle pertains to the surface normals.

GridAspectRatio

Gets or sets the maximum allowed aspect ratio of sampling quads.

GridMaxCount

Gets or sets the maximum number of grid quads in the initial sampling grid.

GridMinCount

Gets or sets the minimum number of grid quads in the initial sampling grid.

JaggedSeams

Gets or sets whether or not the mesh is allowed to have jagged seams. When this flag is set to true, meshes on either side of a Brep Edge will not match up.

MaximumEdgeLength

Gets or sets the maximum allowed mesh edge length.

Minimal

Gets minimal meshing parameters.

MinimumEdgeLength

Gets or sets the minimum allowed mesh edge length.

MinimumTolerance

Gets or sets the minimum tolerance.

QualityRenderMesh

Gets mesh creation parameters to create the a render mesh when mesh quality is preferred over meshing speed.

RefineAngle

Gets or sets the mesh parameter refine angle in radians.

RefineAngleInDegrees

Gets or sets the mesh parameter refine angle in degrees.

RefineGrid

Gets or sets a value indicating whether or not the sampling grid can be refined when certain tolerances are not met.

RelativeTolerance

Gets or sets the relative tolerance.

SimplePlanes

Gets or sets a value indicating whether or not planar areas are allowed to be meshed in a simplified manner.

Smooth

Gets mesh creation parameters for smooth meshing.
This corresponds with the "Smooth and Slower" default in Rhino.

TextureRange

Gets or sets how and if textures will be packed.

Tolerance

Gets or sets the maximum allowed edge deviation. This tolerance is measured between the center of the mesh edge and the surface.

Methods (12)

CopyFrom(MeshingParameters source)

Call this method to copy MeshingParameters from another instance.

Dispose()

Actively reclaims unmanaged resources that this instance uses.

Dispose(Boolean disposing)

For derived class implementers.
This method is called with argument True when class user calls Dispose(), while with argument False when the Garbage Collector invokes the finalizer, or Finalize() method.
You must reclaim all used unmanaged resources in both cases, and can use this chance to call Dispose on disposable fields if the argument is true.
Also, you must call the base virtual method within your overriding method.

DocumentCurrentSetting(RhinoDoc doc)

Gets the MeshingParameters that are currently set for a document. These are the same settings that are shown in the DocumentProperties "mesh settings" user interface.

Equals(MeshingParameters other)

Determines whether the specified MeshingParameters has the same values as the present MeshingParameters.

Equals(Object obj)

Determines whether the specified MeshingParameters has the same values as the present MeshingParameters.

FromEncodedString(String value)

Converts encoded serialized string into a MeshingParameters

GetHashCode()

Computes a hash number that represents the current MeshingParameters.

GetObjectData(SerializationInfo info,StreamingContext context)

SetSubDDisplayParameters(SubDDisplayParameters subDDisplayParameters)

Sets the SubD display parameters.

SubDDisplayParameters()

Gets the SubD display parameters.

ToEncodedString()

Returns a encoded string that represents the MeshingParameters.

Operators (2)

Determines whether the two MeshingParameters do not have equal values.

Determines whether the two MeshingParameters have equal values.

Nothing found